Casambi®/DALI control in a surface-mounted ceiling housing. The control module is built in and included in the scope of delivery. It translates Casambi® commands into DALI commands and is added to your Casambi® mesh in the usual way. You then control your DALI control gear via the Casambi® app and via linked push buttons, sensors and remote controls – no gateway, no hub required.
A 48 V track docks onto the bay (27 mm wide, 40 mm high, full housing height) on one short side, compatible with STUCCHI® Evo ST2.
Power supply
The module is connected to the 230 V mains cable from the ceiling and generates the DALI bus current itself. On its top it provides through-wiring terminals that carry the mains voltage onward.
There are two ways of supplying the track with 48 V:
- In-line transformer in the track: A 48 V in-line transformer (up to 250 W depending on version) is clipped into the track and supplied with 230 V via the module's through-wiring terminals. In the DALI version the transformer carries the DALI signal into the track via an additional contact – so the control commands reach the DALI spotlights in the track.
- Central transformer: The 48 V transformer sits e.g. in the distribution board. The 48 V is fed into the track via a feed-in from the track manufacturer; the cable is inserted from the short side of the feed-in. In this case, too, the module needs a 230 V supply line. For this set-up a MOUNTME® housing with cable outlet is the better choice, e.g. MOUNTME® Ninetyone DALI / Ninetytwo DALI.
48 V transformers are not included in the scope of delivery.
Mounting on the ceiling improves the radio connection of the Casambi® module and heat dissipation.
DALI functions
The module is DALI controller and DALI bus power in one – no separate DALI bus power supply is needed. You select the control mode in the Casambi® app via the device profile; in most profiles the module assigns the DALI addresses itself.
- Broadcast dimming (factory setting): all connected DALI devices together, without addressing.
- Two channels: dim two addresses separately – either as short addresses or as DALI groups 0 and 1.
- Up to six channels: six dimming sliders, one per DALI address.
- Tunable White (DT8): brightness and colour temperature 2,700–6,500 K, jointly for up to 6 drivers or as two separately dimmable TW channels with a common colour temperature.
- RGB (DT6): colour field and dimming slider.
- DALI sensor: presence and daylight sensor on the bus, also in combination with broadcast and Tunable White.
DALI planning note
The bus is supplied with a guaranteed 20 mA, and no more than 6 DALI devices can be addressed. Every item of control gear and every sensor draws current from the bus. Add up the bus current consumption of all connected devices according to their data sheets – the total must not exceed 20 mA.
Technical data
| Control | Casambi® Bluetooth mesh: app, push buttons, sensors, remote controls – no gateway, no hub |
| Radio | 2,400–2,480 MHz, max. +8 dBm |
| Range | indoors up to 30 m, open field up to 50 m |
| Output | DALI (compatible) with integrated bus power |
| DALI bus current | 20 mA (guaranteed) |
| DALI devices | max. 6 |
| Mains voltage | 220–240 V AC, 50/60 Hz |
| 230 V onward wiring | through-wiring terminals on top of the module, up to 16 A |
| Power consumption | max. 1.5 W, standby typ. < 0.5 W |
| Max. temperature at module | 70 °C |
| Protection rating | IP20, for dry indoor areas only |
| Housing | 130 × 33 × 40 mm (L × W × H) |
| Material | plastic |
| Cable entry | 2 × Ø 15 mm in the mounting plate |
| Bays | 1 × 27 mm wide, 40 mm high, full housing height, on one short side |
| Compatible track | 48 V, e.g. STUCCHI® Evo ST2 |
Scope of delivery
Housing with mounting plate and built-in Casambi®/DALI control module. Not included: 48 V transformers, DALI control gear, luminaires, tracks and their feed-ins.
Note: Please have the installation carried out by a qualified electrician. This keeps the 230 V connection safe and your luminaire working reliably.